Independent informational guide. It is not an installer and does not provide personal or technical advice.

Backup planning

How to evaluate solar battery backup runtime

Battery runtime is not a whole-house promise. It depends on usable energy, available power and the loads that remain on.

Illustrative rooftop-panel image; it does not depict a Puerto Rico project or provider. Photo: Dr. Chinchu C., CC BY 4.0. Dr. Chinchu C. · CC BY 4.0 · Change: resized and converted to WebP. · Derivative license: CC BY 4.0.

Usable energy versus power

Battery capacity is energy, usually stated in kWh. It is the reserve available over time. Power is the demand the battery and inverter can serve at once. A proposal needs both figures for the exact model; one is not a substitute for the other.

Dividing stated capacity by an estimated load is only a planning approximation. It does not prove the system can start or sustain a particular appliance. Backup configuration, inverter limits and equipment settings matter. Ask for the manufacturer documentation for the proposed model.

DOE says a residential system needs appropriately configured inverter equipment and storage to operate on its own during an outage. That is why runtime is separate from the question of whether the system can provide backup at all. Confirm the backup configuration first.

  • Request nominal and usable capacity.
  • Request continuous power and any starting-load limit.
  • Ask which part of the home is included in backup.

Source: Solar and Resilience Basics, Enphase Energy System with IQ Battery 5P Owner’s Guide

Loads you want to support

Start with priorities rather than the phrase whole home. Selected lights, refrigeration, communications, documented medical equipment and chosen outlets can have very different needs. Write down what must run, when it is needed and how long you hope to prioritize it.

For each load, retain a label, manual or professional measurement that describes consumption and starting behavior. Do not assume two appliances with the same nameplate rating behave the same way. Motors, cooling and heating loads need configuration-specific review.

Turn the list into an operating decision: what remains on by default, what stays off, and who understands that plan. It also lets you discuss system sizing without treating this page as a design calculator.

Critical-load worksheet
LoadWhen neededFact to confirm
RefrigerationContinuous or intervalsActual use and starting demand
LightingNight or safetyIncluded circuits
Internet and communicationsDuring an outageEquipment power
Other priority loadHousehold-specificModel and backup requirement

Source: Enphase Energy System with IQ Battery 5P Owner’s Guide

What changes runtime

Household demand changes throughout the day. Simultaneous use, a refrigerator cycling, temperature and high-demand loads can shorten an estimate. Runtime also depends on the state of charge when an outage begins and the system’s reserve setting.

Solar production may help in some documented configurations and conditions, but it should not be added as guaranteed hours. Sun, clouds, shading, inverter settings and control limits all change the contribution. Use a conservative scenario that a qualified reviewer can tie to the actual equipment.

Some manufacturer monitoring or control features require an active internet connection. Ask which local backup functions, app controls and alerts are available in the proposed configuration rather than assuming an online feature proves outage performance.

  • Starting state of charge and reserve.
  • Simultaneous loads and starting peaks.
  • Inverter and backup configuration limits.
  • Potential solar contribution, without promising it.

Source: Enphase Energy System with IQ Battery 5P Owner’s Guide

Examples with visible assumptions, if approved

A useful worksheet can show stated usable energy, documented loads and a target period. It should not publish a universal runtime because model limits, state of charge and use pattern are not known from a generic article.

Ask the installer to show what changes when a load is added, another is limited, or reserve changes. The review should distinguish energy available from simultaneous power.

Do not use an editorial estimate for medical equipment, safety-critical needs or whole-home decisions. Those cases need a qualified review of loads, configuration and manufacturer instructions.

Questions for your installer

Request a written answer naming the battery, inverter and supported circuits or loads. Ask what scenario was evaluated and what is excluded. The identified installer, not this publisher, evaluates, installs and quotes.

Ask how the system behaves during an outage, which conditions affect backup and which documents govern the equipment. Then place the answers in a quote comparison worksheet and map documents in the warranty guide.

  • What usable energy does this exact model provide?
  • What continuous and starting power applies?
  • Which circuits are backed up?
  • What assumptions and exclusions are written down?

Source: Solar and Resilience Basics

Questions

Does a battery always back up the whole home?

No. Scope depends on documented configuration, power and selected loads; request that scope in writing.

Source: Solar and Resilience Basics

Prepare a like-for-like comparison

Use a documented checklist to compare equipment, scope, warranties, payment terms and unresolved questions.

Compare solar quotes

Sources

  1. Solar and Resilience Basics — U.S. Department of Energy, 2026-11-15
  2. Enphase Energy System with IQ Battery 5P Owner’s Guide — Enphase Energy, 2026-11-15